How to Fix Door gasket worn on LG LRSXS2706V (Side-by-Side)

Door gasket worn

This step-by-step repair guide walks you through fixing door gasket worn on your LG LRSXS2706V (Side-by-Side). With the right tools and parts, most homeowners can complete this repair in 1–2 hours and avoid a costly service call.

Part of our Top 20 Refrigerator Models & Common Repair Issues Guide. Browse all refrigerator repair guides for related models and issues.

“`html

Common Symptoms & Causes

If your LG LRSXS2706V has a worn door gasket, you may notice several telltale signs affecting both compartments.

Condensation or frost buildup along the inner edges of the refrigerator or freezer door
Food spoiling faster than usual due to inconsistent internal temperatures
The refrigerator runs continuously without cycling off normally
A visible gap or cracked, brittle sections along the door seal when inspected by hand

These issues are typically caused by age-related deterioration of the gasket material, repeated door use causing the seal to lose flexibility, or food residue buildup that permanently deforms the rubber over time.

“`

Safety First

Unplug the refrigerator from the power outlet before starting any repair — never work on a live appliance.
Shut off the water supply valve before disconnecting any water lines or hoses.
Wear work gloves when handling metal brackets, sheet metal edges, or sharp components.
Take photos with your phone before disconnecting any wiring harnesses or connectors.
Work in a well-lit area with enough floor space to lay removed panels flat.

Tools & Parts Needed

Essential Tools

Phillips #2 screwdriver
¼” nut driver
Needle-nose pliers
Multimeter
Flashlight or work light

Replacement Parts

Step-by-Step Repair Instructions

Step 1

Slide a dollar bill along all four edges of both doors, pulling it out at 6-inch intervals to feel for drag. Missing resistance at any point reveals exactly where the gasket has lost its seal, which causes warm air infiltration, excess compressor runtime, and frost buildup inside the fridge. Mark those weak spots with tape so you can target them precisely in the next step.

Step 2

Using a hair dryer on its lowest heat setting held 4–5 inches away, warm any stiff or kinked gasket sections for about 2 minutes until the rubber becomes pliable. Heat relaxes the vinyl so it can be reshaped; skipping this on a cold, rigid gasket risks cracking it further and wasting the repair. Work the softened rubber firmly back into the retainer channel starting at the corners, since corners are where the gasket most commonly pulls loose first.

Step 3

If the gasket is visibly torn, permanently flattened, or won’t hold its shape after reconditioning, replacement is the only reliable fix. Carefully peel the old gasket out of its retaining groove all the way around the door, then wipe the groove clean with a warm, soapy cloth to remove grease, mold, and any debris that would prevent the new gasket from seating flush. A dirty groove is the most common reason a new gasket leaks immediately after installation, so don’t skip the cleaning step.

Step 4

Press the new gasket into the retainer groove using only your fingers, beginning at the top two corners to anchor it and then working down each side evenly. LG designs this gasket for a tool-free, adhesive-free friction fit, so no glue or clips are needed — forcing it with a tool can tear the lip or distort the seal profile. If a section won’t seat fully, a brief pass with the hair dryer will soften it enough to push flush without damage.

Step 5

If the dollar-bill test still shows weak spots after a new gasket is installed, the door itself may be sitting crooked and compressing the gasket unevenly. Loosen the top hinge bolt using a 3/8-inch socket driver just enough to allow slight movement, shift the door until the gap between the door and cabinet is uniform from top to bottom, then re-tighten the bolt firmly. Always unplug the refrigerator before adjusting hinges to avoid accidental contact with electrical components near the hinge area.

Step 6

With the repair complete, perform a final dollar-bill test by closing each door on the bill at 6-inch intervals around the entire perimeter of both doors. You should feel consistent, moderate resistance every time you pull the bill out — any point where it slides freely indicates a remaining seal gap that needs further attention. Running this check immediately after reassembly saves you from discovering a failed repair only after spoiled food or a high electricity bill.

Where to Buy Replacement Parts

Find genuine OEM and aftermarket replacement parts for your LG LRSXS2706V (Side-by-Side) on Amazon:

When to Call a Professional

If the issue persists after completing all steps above, the problem may involve the sealed refrigerant system, a failed main control board, or wiring that requires specialized diagnostic equipment. Contact a licensed appliance technician — attempting sealed-system repairs without EPA 608 certification is illegal and unsafe.

“`html

How Much Does This Repair Cost?

A replacement door gasket for the LG LRSXS2706V typically costs between $30 and $75 in parts alone. Professional appliance repair services generally charge $150 to $300 once you factor in the service call and labor fees. Tackling this repair yourself can save you $100 or more, making it a smart and budget-friendly DIY project.

“`

Frequently Asked Questions

How do I know if the door gasket on my LG LRSXS2706V needs replacing?

Check for visible cracks, tears, or stiff sections in the rubber seal. If cold air escapes or moisture forms around the door edges, the gasket is no longer sealing properly.

Can I replace the LG LRSXS2706V door gasket myself?

Yes, it’s a manageable DIY repair requiring no special tools. Simply pull the old gasket free from the door liner groove and press the new one firmly into place.

Where can I find a replacement gasket for the LG LRSXS2706V?

Order a genuine replacement using your model number directly from LG’s parts website or authorized retailers like RepairClinic or PartSelect to ensure a proper fit.

Post Views: 0