How to Fix F10 error — runaway temperature on Frigidaire FGGH3047VF (Gas Range)

F10 error — runaway temperature

In this guide, I’ll walk you through fixing the F10 error — runaway temperature on your Frigidaire FGGH3047VF (Gas Range). With the right tools and parts, most homeowners can complete this repair in about 1–2 hours and save themselves a costly service call.

Part of our Top 20 Oven Models & Common Repair Issues Guide. Browse all oven repair guides for related models and issues.

Common Symptoms & Causes

You may see these symptoms when your Frigidaire FGGH3047VF triggers an F10 runaway temperature error:

• The oven display shows the “F10” error code during or after a baking cycle
• The oven keeps heating beyond the set temperature and won’t stop
• The control board emits a continuous beeping alarm alongside the F10 code
• The oven feels excessively hot near the door or control panel even at low settings

The most common reason for this issue is a faulty oven temperature sensor (RTD probe) sending incorrect resistance readings. It could also be due to a failing control board that no longer regulates the heating output properly.

Safety First

• Unplug the oven from the power outlet before starting any repair — never work on a live appliance.
• Wear work gloves when handling metal brackets, sheet metal edges, or sharp components.
• Take photos with your phone before disconnecting any wiring harnesses or connectors.
• Work in a well-lit area with enough floor space to lay removed panels flat.

Tools & Parts Needed

Essential Tools

• Phillips #2 screwdriver
• ¼” nut driver
• Multimeter
• Work gloves (heat-rated)
• Flashlight

Replacement Parts

• Oven temperature sensor
• control board
• multimeter

Step-by-Step Repair Instructions

Step 1

First things first, unplug the range immediately. The F10 error means the control board is detecting a continuous runaway temperature, which can scorch the oven interior or worse, trigger a fire. This is not a false alarm — the board genuinely believes the oven is overheating without stopping. Don’t restore power until you’ve diagnosed the root cause.

Step 2

After the oven cools for at least 30 minutes, test the temperature sensor mounted on the oven back wall (two Phillips screws, two-pin harness). A healthy sensor should read 1,080–1,100Ω at room temperature. If you see a reading below 900Ω, the sensor has shorted and is sending a falsely extreme temperature signal to the board, triggering the F10 error. If the sensor fails this test, replace it before assuming the control board is the issue — it’s the most common and least expensive fix.

Step 3

Once you’ve installed the new sensor, restore power and run the oven briefly to check if the F10 error returns. If it does, with a known-good sensor, the control board is likely failing to regulate temperature correctly and must be replaced. The correct replacement board for this model is part number 316576601. Do not continue using the range if the board is malfunctioning, as runaway temperature presents a real burn and fire hazard.

Step 4

To access the control board, remove the backsplash panel by taking out the two Phillips screws at each end and lifting the panel straight off. The board sits behind the console beneath it. Always work with the range unplugged during this step; photographing all harness connections before you touch anything will save you significant time during reassembly.

Step 5

Unplug every harness connector from the old board, then remove the four Phillips mounting screws securing it to the chassis. Install the new board in the same orientation, reconnect all harnesses by matching your reference photos, and replace the backsplash panel before restoring power. A missed connector is often why a new board appears to fail immediately, so verify every connection before the first power-on.

Step 6

With the repair complete, run the oven at 350°F for at least 20 minutes with an independent oven thermometer placed inside. The temperature should climb to target, stabilize within roughly ±25°F, and hold without triggering the F10 error — steady stabilization confirms both the sensor and board are communicating correctly. If the error returns during this controlled test, double-check all harness connections before considering any further diagnosis.

Where to Buy Replacement Parts

You can find genuine OEM and aftermarket replacement parts for your Frigidaire FGGH3047VF (Gas Range) on Amazon:

• Frigidaire FGGH3047VF oven temperature sensor 316217002 replacement
• Frigidaire gas range control board 316576601 replacement
• Frigidaire oven F10 runaway temperature fix

When to Call a Professional

If you still experience issues after following all the steps above, the problem may involve a failed main control board, a defective temperature sensor or high-limit thermostat, or wiring that requires specialized diagnostic equipment. At that point, it’s best to contact a licensed appliance technician. And remember, on gas models, don’t attempt to work on the gas valve, burner orifices, or supply line — that work is restricted to a licensed gas fitter in most jurisdictions.

How Much Does This Repair Cost?

If you’re considering a DIY approach, parts for fixing an F10 runaway temperature error on the Frigidaire FGGH3047VF typically cost between $20–$150, depending on whether you’re replacing the oven temperature sensor, control board, or both. A professional service call for this repair usually runs $150–$300, including labor. Tackling this repair yourself can save you $100 or more in labor costs alone.

Frequently Asked Questions

Is it safe to keep using my Frigidaire FGGH3047VF while the F10 error is active?

No, you should stop using the range immediately until the issue is resolved. A runaway temperature condition can create a fire hazard or permanently damage the oven’s control board.

What part most commonly causes the F10 error on the FGGH3047VF?

The RTD oven temperature sensor is the most frequent culprit. A faulty sensor sends incorrect readings to the control board, triggering the runaway temperature fault.

Can I reset the F10 error by simply unplugging the range?

Unplugging the range may temporarily clear the error, but it will return if the underlying sensor or control board issue isn’t repaired. Always diagnose the root cause before restoring power.

Recommended Products

Here’s a list of parts and tools I recommend for this repair, based on compatibility and customer reviews:

• 316217002 Oven Temperature Sensor Probe for Frigidaire Gallery/Kenmore/Electrolux Ranges – Range Oven Sensor, Replaces AP3363354 316111201 318087600
• 316217002 Oven Temperature Sensor for Frigidaire Kenmore Stove and Oven

As an Amazon Associate, I earn from qualifying purchases.

The RTD Sensor That Stops the F10 Runaway Temperature Error

When your FGGH3047VF throws an F10 error, the RTD temperature probe is almost always the culprit — and this is the exact replacement part that fits and solves the problem on this model. I replace this sensor more often than anything else on this range, and it takes about 15 minutes to swap out.

What works

• Drops right in without modification — the connector and probe diameter match the original exactly, so you’re not forcing it or hunting for adapters.
• The error clears immediately after installation and the oven holds temperature stable, which tells you the board is fine and the sensor was genuinely failed.
• Comes with clear part number cross-references (AP3363354, 316111201, 318087600), so you know you’re ordering the right thing even if Frigidaire’s documentation is vague.

What doesn’t

• Occasionally you’ll order this only to discover the control board is actually the problem (happens maybe 10% of the time), so keep your receipt handy just in case the error persists after swap.
• The probe sits deep in the oven wall cavity, so getting your hands in there is tight if your range is wedged against a cabinet — you may need to pull the range out a few inches for comfortable access.

I’ve had homeowners order a control board first thinking the sensor was fine, only to end up needing this part anyway — so test with a multimeter across the sensor pins before you buy anything, just to confirm it’s actually open or out of range. That said, on this model the odds are strongly in your favor. 316217002 Oven Temperature Sensor Probe for Frigidaire Gallery/Kenmore/Electrolux Ranges

This post contains affiliate links. As an Amazon Associate, I earn from qualifying purchases at no extra cost to you.