Frigidaire FGMV17WNVF Turntable Motor Replacement – Step-by-Step Guide

I’ve worked on dozens of Frigidaire over-the-range microwaves, and the FGMV17WNVF turntable motor is one of the more frequent calls I get — especially on units that are 3–5 years old. Nine times out of ten, when the turntable stops spinning or starts grinding, the motor itself is the culprit and a straightforward replacement solves it completely.

Dave Holt — Certified Appliance Repair Technician

Experience: 15+ years servicing residential & commercial appliances • Certifications: EPA 608 Certified, NATE-recognized technician • Former lead technician at a multi-state appliance service company • Specialties: Washers, dryers, refrigerators, dishwashers, ovens, microwaves, ice makers

Turntable Motor Replacement Guide

If your Frigidaire FGMV17WNVF over-the-range microwave turntable is not spinning due to motor failure, replacing the turntable motor is a MODERATE difficulty repair. The turntable motor rotates the glass plate to ensure even heating. This repair requires accessing the bottom of the microwave.

🔨 Pro Tip from Dave

When replacing the turntable motor on the FGMV17WNVF, order part number 5304464061 — it’s the correct OEM motor for this unit. A common mistake I see is techs forgetting to clean the motor shaft socket before installing the new unit, which causes the coupling to sit unevenly and leads to premature failure again. Also, the three mounting screws strip easily on this model, so use a properly sized Phillips head and don’t overtorque them.

Symptoms of Turntable Motor Failure

Common signs that indicate turntable motor failure:

Turntable doesn’t rotate at all
Turntable starts then stops
Grinding or humming noise from the bottom
Motor burned out – was working then stopped
Visible damage or burning smell from motor
Uneven heating due to non-rotating turntable

⚠️ Safety Warning

Always unplug the microwave before beginning any repair. Wait 60 seconds after unplugging to allow capacitors to discharge. The turntable motor area is at the bottom of the microwave and is generally low-voltage, but safety precautions are still essential.

Parts Needed

Check each product page for other buying options. (Part #: 5304464119)

Note: You may also want to check the roller ring and turntable coupling if they show signs of wear or damage.

Tools Required

Phillips Screwdriver – #2 size
Needle-Nose Pliers – For wire connections
Flashlight – To see under the microwave
Clean cloth – For cleaning the motor area

Step-by-Step Instructions

Step 1: Unplug and Prepare

Unplug the microwave from the wall outlet. Remove the glass turntable plate and the roller ring from inside the microwave. Set them aside in a safe location. Turn the microwave upside down or on its side to access the bottom panel.

Step 2: Remove the Bottom Panel

Locate the screws securing the bottom panel. There are typically 4-6 screws around the perimeter. Remove all screws using your Phillips screwdriver. Some models may have clips in addition to screws. Gently lift the bottom panel away to expose the turntable motor area.

Step 3: Locate the Turntable Motor

The turntable motor is located in the center of the bottom area. It’s a small motor with a shaft that extends up through the bottom of the microwave. The motor has wire connections and is typically mounted with screws or clips.

Step 4: Inspect the Motor

Before removing, inspect the motor:

Check for visible damage, burning, or overheating
Look for loose wires or damaged connectors
Inspect the motor shaft for damage
Check the coupling between motor and roller ring
Verify the motor is the problem (not the roller ring or support)

Step 5: Disconnect the Motor Wires

The turntable motor has wire connections. Use needle-nose pliers to gently pull the wire connectors off the motor terminals. Take a photo before disconnecting to ensure proper reconnection. The wires are typically color-coded.

Step 6: Remove the Motor Mounting Hardware

The motor is secured with screws or clips. Remove the mounting screws using your Phillips screwdriver. Some motors may have a bracket that needs to be removed. Carefully remove all mounting hardware and set it aside.

Step 7: Remove the Old Motor

Once all mounting hardware is removed, gently pull the motor away from its mounting location. The motor shaft extends through the bottom, so you may need to pull it down carefully. Remove the old motor completely.

Step 8: Clean the Motor Area

While the motor is removed, clean the motor area:

Remove any debris, grease, or food particles
Clean the area where the new motor will mount
Wipe down the motor shaft opening
Ensure the area is dry before installing the new motor

Step 9: Install the New Motor

Position the new Frigidaire 5304464119 turntable motor in the same location as the old one. Ensure the motor shaft extends properly through the bottom opening. The motor should sit flush against the mounting surface. Secure it with the mounting screws, being careful not to overtighten.

Step 10: Reconnect the Wires

Refer to your photo and reconnect the wires to the new motor terminals. Push the connectors firmly onto the terminals until they click into place. Ensure all connections are secure.

Step 11: Reinstall the Roller Ring and Plate

Turn the microwave right-side up. Place the roller ring in the bottom of the cavity (it sits on the motor shaft or support). Then place the glass turntable plate on top of the roller ring. Ensure everything sits level.

Step 12: Test the Installation

Plug the microwave back into the wall outlet. Place a cup of water in the center of the turntable. Start a 30-second cooking cycle. Watch to ensure:

The turntable rotates smoothly
No grinding or unusual noises
The turntable remains level during rotation
Rotation is steady and consistent

Troubleshooting

If the turntable still doesn’t rotate after replacement:

Verify wire connections are secure
Check the roller ring for damage (may also need replacement)
Inspect the turntable support (may be damaged)
Ensure the motor shaft is properly aligned
Check for obstructions preventing rotation
Verify you have the correct motor for your model

Maintenance Tips

To extend the life of your new turntable motor:

Keep the turntable area clean and free of food debris
Don’t overload the turntable with heavy dishes
Ensure the glass plate sits level and isn’t warped
Clean the roller ring regularly
Avoid slamming the door, which can damage the motor mechanism

When to Call a Professional

Consider professional help if:

Multiple components need replacement
The problem persists after replacement
You’re not confident in your ability to properly install the motor

← Back to Top 20 Microwave Models & Common Repair Issues Guide

How Much Does This Repair Cost?

The replacement turntable motor (part 5304464061) typically runs $20–$40 for DIY repair, making this one of the most budget-friendly microwave fixes available. A professional repair shop will generally charge $100–$180 total once you factor in labor, so doing it yourself delivers significant savings on what is ultimately a simple swap.

Recommended Products

These are the parts and tools we recommend for this repair, based on compatibility and customer reviews:

As an Amazon Associate, I earn from qualifying purchases.

Post Views: 3