Magnetron Replacement Guide
\n\n\n\nIf your Frigidaire FFMV1745TS over-the-range microwave has no heating function and food stays cold, the magnetron has likely failed. The magnetron generates the microwaves that cook your food. This is an ADVANCED repair that requires working with high-voltage components. Replacing the magnetron is expensive but doable for experienced DIYers.
\n\n\n\n⚠️ CRITICAL SAFETY WARNING
\n\n\n\nThis repair involves HIGH VOLTAGE components that can be LETHAL. The magnetron operates at over 2,000 volts. You MUST:
\n\n\n\n- \n
- Unplug the microwave and wait at least 60 seconds \n
- Discharge the high-voltage capacitor before touching ANY components \n
- Wear insulated gloves rated for high voltage \n
- Keep one hand behind your back (prevents current path through heart) \n
- Use a discharge tool to safely discharge the capacitor \n
- If you’re uncomfortable with high voltage, call a professional \n
Symptoms of Magnetron Failure
\n\n\n\nCommon signs that indicate magnetron failure:
\n\n\n\n- \n
- Microwave runs but food doesn’t heat or stays cold \n
- Humming sound but no heating \n
- Sparking or arcing inside the microwave cavity \n
- Burning smell during operation \n
- Microwave shuts off after a few seconds of operation \n
Parts Needed
\n\n\n\n- \n
- Frigidaire 5304464116 Magnetron (Part #: 5304464116) \n
Note: Magnetrons are expensive ($150-300). Verify the magnetron is the problem before purchasing, as other components can cause similar symptoms.
\n\n\n\nTools Required
\n\n\n\n- \n
- Digital Multimeter – For testing components \n
- Phillips Screwdriver Set – Various sizes \n
- Needle-Nose Pliers – For wire connections \n
- High-voltage discharge tool – CRITICAL for safety \n
- Insulated gloves – Rated for high voltage \n
- Safety glasses – Protection from debris \n
- Flashlight – To see inside the case \n
Step-by-Step Instructions
\n\n\n\nStep 1: Unplug and Discharge Capacitor
\n\n\n\nUnplug the microwave from the wall outlet. Wait at least 60 seconds. This is CRITICAL – the high-voltage capacitor can hold a lethal charge. Use a discharge tool (screwdriver with insulated handle) to short the capacitor terminals. Touch the tool across both terminals simultaneously. You may hear a pop or see a spark – this is normal. Repeat this discharge 3-4 times to ensure it’s fully discharged.
\n\n\n\nStep 2: Remove the Outer Case
\n\n\n\nLocate and remove all screws from the rear and side panels. The Frigidaire FFMV1745TS typically has 8-12 screws. Remove all visible screws and set them aside in an organized manner. Gently lift the panels away, being careful not to damage any wires.
\n\n\n\nStep 3: Locate the Magnetron
\n\n\n\nThe magnetron is a large, cylindrical component with cooling fins, typically located on the right side of the microwave. It has a large antenna (waveguide) that extends into the cooking cavity. You’ll see two large wire connections (filament wires) and it’s mounted with 4 screws.
\n\n\n\nStep 4: Test the Magnetron (Optional but Recommended)
\n\n\n\nBefore replacing, test the magnetron with your multimeter to confirm it’s the problem:
\n\n\n\n- \n
- Set multimeter to resistance/ohms mode \n
- Test filament terminals (should show 0.1-3 ohms resistance) \n
- Test between filament and case (should show infinite resistance/open circuit) \n
- If filament shows open circuit or very high resistance, magnetron is bad \n
- If resistance to case is low, magnetron has internal short (definitely bad) \n
Step 5: Disconnect the Magnetron Wires
\n\n\n\nThe magnetron has two large wire connections (filament wires) that connect to the high-voltage transformer. These are typically held with spade connectors. Use needle-nose pliers to gently pull the connectors off. Take detailed photos before disconnecting – these connections are critical and must be reconnected correctly.
\n\n\n\nStep 6: Remove the Waveguide Cover
\n\n\n\nThe magnetron antenna extends through a waveguide into the cooking cavity. There’s a cover (usually mica or ceramic) over the waveguide opening inside the cavity. Remove this cover carefully – it may be held with screws or clips. Set it aside – you’ll need to replace it or clean it.
\n\n\n\nStep 7: Remove the Magnetron Mounting Screws
\n\n\n\nThe magnetron is secured with 4 mounting screws. These may be in tight spaces. Use your Phillips screwdriver to remove all 4 screws. The magnetron is heavy, so support it as you remove the last screw.
\n\n\n\nStep 8: Remove the Old Magnetron
\n\n\n\nCarefully pull the magnetron away from the mounting bracket. The antenna extends through the waveguide, so you may need to wiggle it slightly. Be gentle – the waveguide and antenna are delicate. Once free, remove the magnetron completely.
\n\n\n\nStep 9: Clean the Waveguide
\n\n\n\nWhile the magnetron is removed, inspect and clean the waveguide. Look for signs of arcing, burning, or damage. Clean any debris or food particles. If the waveguide is damaged, it may need repair or the microwave may need professional service.
\n\n\n\nStep 10: Install the New Magnetron
\n\n\n\nPosition the new Frigidaire 5304464116 magnetron in the same location as the old one. Ensure the antenna extends properly through the waveguide opening. The magnetron should sit flush against the mounting bracket. Secure it with the 4 mounting screws, being careful not to overtighten.
\n\n\n\nStep 11: Reconnect the Filament Wires
\n\n\n\nRefer to your photos and reconnect the filament wires to the magnetron terminals. Push the spade connectors firmly onto the terminals. Ensure both connections are secure – loose connections can cause arcing and failure. Double-check that the connections match your photos exactly.
\n\n\n\nStep 12: Replace the Waveguide Cover
\n\n\n\nInstall a new or cleaned waveguide cover over the opening in the cooking cavity. This cover prevents food splatters from entering the waveguide and causing arcing. Ensure it’s properly secured and sits flush.
\n\n\n\nStep 13: Reassemble the Microwave
\n\n\n\nCarefully replace all panels, ensuring no wires are pinched or damaged. Reinstall all screws in their original locations. Tighten securely but don’t overtighten.
\n\n\n\nStep 14: Test the Installation
\n\n\n\nPlug the microwave back into the wall outlet. Place a cup of water in the center of the turntable. Start a 1-minute cooking cycle on high power. Monitor for:
\n\n\n\n- \n
- Water should heat up (feel the cup after 1 minute) \n
- No unusual sounds or sparking \n
- No burning smells \n
- Microwave should run for the full cycle without shutting off \n
If the water doesn’t heat, or you see sparking/smelling burning, immediately unplug and recheck your work.
\n\n\n\nTroubleshooting
\n\n\n\nIf the microwave still doesn’t heat after replacement:
\n\n\n\n- \n
- Verify all wire connections are secure (check with multimeter) \n
- Test the high-voltage diode (may also be faulty) \n
- Check the high-voltage capacitor (may need replacement) \n
- Inspect the high-voltage transformer for damage \n
- Verify the door switches are working (they prevent operation) \n
- Check for damaged waveguide or antenna \n
When to Call a Professional
\n\n\n\nThis is an ADVANCED repair. Consider professional help if:
\n\n\n\n- \n
- You’re uncomfortable working with high-voltage components \n
- You don’t have proper safety equipment (discharge tool, insulated gloves) \n
- The waveguide shows signs of damage or burning \n
- Multiple components need replacement \n
- You’re not confident in your ability to safely discharge the capacitor \n
\n\n\n\n
← Back to Top 20 Microwave Models & Common Repair Issues Guide
\nRecommended Products
LG 6324W1A001L Genuine OEM Magnetron for LG Microwaves
# Product Recommendation While the blog post focuses on Frigidaire microwave repairs, homeowners with LG microwaves facing similar magnetron failures will find the LG 6324W1A001L Genuine OEM Magnetron an excellent replacement solution that ensures compatibility and reliable performance. This genuine OEM part is engineered to match LG’s exact specifications, eliminating guesswork and the risk of installing an incompatible aftermarket component that could damage the microwave or create safety hazards. The magnetron’s genuine construction guarantees the proper wattage output and heating consistency needed for optimal microwave performance, while OEM parts typically include better warranty coverage than third-party alternatives. Check current pricing on Amazon.
KOKISO Home Microwave Oven Repair Kit – HV Capacitor 2100V 1.0uF, Diode CL01-12, Slow Blow Fuse 5x20mm, 6x30mm 20A, 6x40mm 0.75A 0.8A 5KV
# Recommendation Paragraph When replacing a magnetron in a Frigidaire microwave like the FFMV1745TS, having the right components on hand is essential for a complete repair, and the KOKISO Home Microwave Oven Repair Kit provides multiple critical parts needed during the process. This kit includes a high-voltage capacitor rated at 2100V, a replacement diode, and an assortment of fuses in various amperage ratings—ensuring that if other components need attention during the repair, all the necessary parts are readily available without additional trips to the supplier. Rather than purchasing individual components separately, this comprehensive kit saves both time and money while reducing the risk of compatibility issues. Check current pricing on Amazon.