How to Fix ProBake uneven heating on LG LSEL6335F (Electric Range)

ProBake uneven heating

This step-by-step repair guide walks you through fixing probake uneven heating on your LG LSEL6335F (Electric Range). With the right tools and parts, most homeowners can complete this repair in 1–2 hours and avoid a costly service call.

Part of our Top 20 Oven Models & Common Repair Issues Guide. Browse all oven repair guides for related models and issues.

“`html

Common Symptoms & Causes

The following symptoms suggest your LG LSEL6335F is experiencing ProBake uneven heating issues that need attention.

Baked goods come out burnt on one side and undercooked on the other
The rear heating element glows visibly brighter or dimmer than normal
Oven temperature reads correctly on display but food cooks unevenly front to back
Preheating takes noticeably longer than the usual 10–15 minutes

These problems are most commonly caused by a failing ProBake rear heating element, a faulty temperature sensor, or a worn oven control board that can no longer regulate heat distribution accurately.

“`

Safety First

Unplug the oven from the power outlet before starting any repair — never work on a live appliance.
Wear work gloves when handling metal brackets, sheet metal edges, or sharp components.
Take photos with your phone before disconnecting any wiring harnesses or connectors.
Work in a well-lit area with enough floor space to lay removed panels flat.

Tools & Parts Needed

Essential Tools

Phillips #2 screwdriver
¼” nut driver
Multimeter
Work gloves (heat-rated)
Flashlight

Replacement Parts

Step-by-Step Repair Instructions

Step 1

Unplug the range from the wall outlet before doing anything else — working on an energized appliance risks electrocution. Uneven baking on the LG LSEL6335F is most often caused by the convection fan failing to spin or the convection element partially burning out, both of which disrupt the even heat circulation that ProBake depends on. Identifying which component has failed first will save you from replacing parts unnecessarily.

Step 2

Remove the four Phillips #2 screws securing the back panel inside the oven cavity and set the panel aside. With power still disconnected, reach in and spin the convection fan blade by hand — it should rotate smoothly and freely with no wobble; a seized or off-balance fan motor will not circulate hot air evenly across the oven. If the blade resists turning or wobbles on its shaft, the fan motor needs to be replaced.

Step 3

The convection element is the loop of resistance wire that surrounds the convection fan, and it is a separate component from the main bake element at the oven floor. Set your multimeter to Rx1 and probe both terminals of the convection element; a reading of OL or open circuit means the element has burned through and must be replaced, since even a partial break will cause drastically uneven heat distribution. A good element will show a low, finite resistance rather than infinite.

Step 4

Place an independent oven thermometer in the center of the oven, set the oven to bake at 350°F, and let it run for a full 30 minutes to reach a stable temperature. If the thermometer reads more than 25°F above or below the set point, the oven needs a calibration offset adjustment — on LG models, press and hold the Bake button for about 5 seconds to access the calibration menu, then dial in the correction. A miscalibrated oven will consistently overbake or underbake regardless of whether the fan and elements are functioning correctly.

Step 5

The oven temperature sensor is a resistance-based probe (RTD) whose resistance value corresponds directly to temperature, so a drifting sensor causes the control board to misread oven temperature and fire the elements incorrectly. With the oven at room temperature, disconnect the sensor leads and measure resistance — you should see approximately 1,080Ω; at a stable 350°F target temperature the reading should rise to approximately 1,183Ω. If your readings deviate significantly from these values, replace the sensor before assuming the control board is at fault.

Step 6

Once all mechanical and electrical checks are complete, perform a real-world ProBake validation by placing a sheet of evenly cut, uniform-thickness cookies or biscuits in the center rack and baking at the manufacturer-recommended temperature. When the convection system is working correctly, every piece on the sheet should be the same shade of golden-brown when you pull it out — dark edges with pale centers, or one side darker than the other, points back to a fan or airflow issue you may have missed. This practical test is more revealing than instrument checks alone because it exposes subtle airflow asymmetry that resistance readings cannot catch.

Where to Buy Replacement Parts

Find genuine OEM and aftermarket replacement parts for your LG LSEL6335F (Electric Range) on Amazon:

When to Call a Professional

If the issue persists after completing all steps above, the problem may involve the sealed refrigerant system, a failed main control board, or wiring that requires specialized diagnostic equipment. Contact a licensed appliance technician — attempting sealed-system repairs without EPA 608 certification is illegal and unsafe.

“`html

How Much Does This Repair Cost?

DIY parts for fixing ProBake uneven heating on the LG LSEL6335F typically run $20–$100, depending on whether you need a new heating element, temperature sensor, or control board. A professional service call for the same repair usually costs $150–$300 in labor alone. Tackling this repair yourself can save you $100–$250 or more.

“`

Frequently Asked Questions

How long does ProBake recalibration take on the LG LSEL6335F?

The recalibration process typically takes 5–10 minutes to complete through the oven’s settings menu. No special tools are required.

Will uneven heating damage my LG LSEL6335F’s bake element permanently?

Not immediately, but prolonged uneven heating can strain the element over time. Addressing the issue promptly helps prevent costly replacements.

Can I fix ProBake uneven heating myself, or do I need a technician?

Many causes, like recalibration or rack positioning, are simple DIY fixes. However, a faulty temperature sensor or control board typically requires a certified LG technician.

Post Views: 0